Wall

All

Showing 1–12 of 24 results

  • Akcansa ASTM C595 Type IL Portland-Limestone Cement

    Read more

    English EPD Document

      EPD document prepared for ASTM C595 Type IL Portland-Limestone Cement  with registration number S-P-04790 has been registered and published in EPD Turkey and The International EPD System. Registered EPD document applies to all global markets. The product investigated in this EPD is not yet on the market. It is the sibling product of the ASTM C150 Type I-II cement manufactured by the same manufacturer, AKÇANSA, and registered on the International EPD® System. The registration code of the sibling product is S-P-04789. The whole production process for both products are the same and only the composition of materials and energy requirements change. A hydraulic cement consisting of two or more inorganic constituents (at least one of which is not Portland cement or Portland cement clinker) which separately or in combination contribute to the strength gaining properties of the cement, (made with or without other constituents, processing additions and functional additions, by intergrading or other blending). As per ASTM C595, Portland-limestone cement (Type IL) shall be a hydraulic cement in which the limestone content is more than 5% but less than or equal to 15% by mass of the blended cement. The investigated product is manufactured at AKÇANSA's Çanakkale Plant. According to the manufacturer, ASTM C595 Type IL Portland-limestone cement has lower clinker and higher gypsum and limestone content compared to ASTM C150 Type I-II cement as reflected in the below composition. Additionally, the energy requirements during the production are 1.1 times higher than its sibling product. Based on these changes, the environmental impacts for A1 (Raw Material Supply) and A3 (Manufacturing) stages has been calculated. Since the product is not yet on the market, all transport related impacts are out of the scope of this EPD. AKCANSA Akçansa, a joint venture of Sabancı Holding and HeidelbergCement, is the largest cement producer of Turkey, and is the leader company of its industry. Akçansa was founded in 1996 as a result of the merger of Akçimento (founded in 1967) and Çanakkale Çimento (founded in 1974). Operating in the Marmara, Aegean, and Black Sea regions, Akçansa produces cement and clinker in its three factories located in Istanbul-Büyükçekmece, Çanakkale, and Samsun-Ladik. Company also has total seven cement terminals located in Istanbul-Ambarlı, İzmir Aliağa, Yalova, Yarımca, Hopa, Derince, and Marmara Ereğlisi. Akçansa merged with its subsidiary Betonsa in 1998 and as a result of this merger, the company started providing service with its “Betonsa” brand and produces concrete at approximately 30 plants in the Marmara, Aegean, and Black Sea regions. The company merged with another subsidiary, Agregasa Agrega, in 2002 and produces aggregate under the brand of “Agregasa” at 4 plants. Akçansa aims to be “the highest quality in production and service” to meet the demands of both its domestic and international customers and to compete beyond the price. Akçansa, the leader of the Turkish cement industry, meets 10 % of Turkey’s cement need as well as 16 % of Turkey’s total cement and clinker export with its products complying to the global quality standards, its eco-friendly identity awarded by the Istanbul Chamber of Industry, its outstanding service understanding, and its plants equipped with high technology.
    View product
  • Adocim CEM I 52.5 N Cement

    Read more

    English EPD Document

      EPD document prepared for Adocim CEM I 52.5 N Cement with registration number S-P-04133 has been registered and published in EPD Turkey and The International EPD System. Registered EPD document applies to all global markets. Cement, one of the most important building materials, is a binding agent that sets and hardens to adhere to building units such as stones, bricks, tiles, etc. Setting and hardening result from hydration, which is a chemical combination of the cement compounds with water that yields sub microscopic crystals or a gel-like material with a high surface area. Cement hardens both in the air and under water and remains in its hardened state once reached. Portland cement is made up of clinker and gypsum. Due to its high clinker content, the strength gain is fast, and the durability is high. It is intended for general use and suitable for both prefabricated applications and conditions where early stripping is required. The declared product is CEM I 52.5 N which compiles with the requirements of EN197-1. The product investigated in this EPD is a special cement type produced at the Artova plant, by ADOÇİM. ADOCİM ADOÇİM CEMENT, started cement production in 1995, is a group company of TITAN CEMENT since 2008. TITAN Cement Group’s roots are backed in 1902 and operates in cement, ready-mix concrete and aggregate fields in more than 15 countries.   ADOÇİM has Integrated Cement Plant in Tokat/Artova, Ready–Mixed Concrete Facilities in Artova, Sivas, Tokat and Çorum in Turkey.   ADOÇİM has a production capacity of 1.300.000 tons/year of clinker and 1.782.000 tons/year of cement production in their integrated cement factory located in Tokat/Artova. The raw material needs of our facility is met by ADOÇİM’s own quarries. Since its foundation, ADOÇİM has maintained a professional approach on eco-friendliness, frugality, worker and occupational safety, quality control and sustainability, and continues to do so today at all its plants. ADOÇİM clinker and cement productions are absolutely guaranteed by continuous quality control activities.   Moreover, ADOÇİM controls its environmental impacts through continuous and observable systems. The company has been worked on Non-Hazardous Waste Recycling and Incineration and also has started to use alternative fuels from disposing of wastes of various industries. ADOÇİM operates according to Turkish Environmental Legislations and also European Union Environmental Policies and Legislation. In ADOÇİM, all key operations carry out within the ISO 14001 framework.   The Artova plant has Environmental Permit and License certificate and continues its activities in a sustainable life cycle to achieve its neutral-carbon target. In addition, with its ISO 9001, ISO 45001, and ISO 50001 management systems certificates, it has a perspective that prioritizes quality, environmentalism, energy efficiency and prioritizes the safety of its employees and all other stakeholders.
    View product
  • Adocim CEM I 42.5 R Cement

    Read more

    English EPD Document

      EPD document prepared for Adocim CEM I 42.5 R Cement with registration number S-P-04132 has been registered and published in EPD Turkey and The International EPD System. Registered EPD document applies to all global markets. Cement, one of the most important building materials, is a binding agent that sets and hardens to adhere to building units such as stones, bricks, tiles, etc. Setting and hardening result from hydration, which is a chemical combination of the cement compounds with water that yields sub microscopic crystals or a gel-like material with a high surface area. Cement hardens both in the air and under water and remains in its hardened state once reached. Portland cement is made up of clinker and gypsum. Due to its high clinker content, the strength gain is fast, and the durability is high. It is intended for general use and suitable for both prefabricated applications and conditions where early stripping is required. The declared product is CEM I 42.5 R which compiles with the requirements of EN197-1. The product investigated in this EPD is a special cement type produced at the Artova plant, by ADOÇİM ADOCİM ADOÇİM CEMENT, started cement production in 1995, is a group company of TITAN CEMENT since 2008. TITAN Cement Group’s roots are backed in 1902 and operates in cement, ready-mix concrete and aggregate fields in more than 15 countries.   ADOÇİM has Integrated Cement Plant in Tokat/Artova, Ready–Mixed Concrete Facilities in Artova, Sivas, Tokat and Çorum in Turkey.   ADOÇİM has a production capacity of 1.300.000 tons/year of clinker and 1.782.000 tons/year of cement production in their integrated cement factory located in Tokat/Artova. The raw material needs of our facility is met by ADOÇİM’s own quarries. Since its foundation, ADOÇİM has maintained a professional approach on eco-friendliness, frugality, worker and occupational safety, quality control and sustainability, and continues to do so today at all its plants. ADOÇİM clinker and cement productions are absolutely guaranteed by continuous quality control activities.   Moreover, ADOÇİM controls its environmental impacts through continuous and observable systems. The company has been worked on Non-Hazardous Waste Recycling and Incineration and also has started to use alternative fuels from disposing of wastes of various industries. ADOÇİM operates according to Turkish Environmental Legislations and also European Union Environmental Policies and Legislation. In ADOÇİM, all key operations carry out within the ISO 14001 framework.   The Artova plant has Environmental Permit and License certificate and continues its activities in a sustainable life cycle to achieve its neutral-carbon target. In addition, with its ISO 9001, ISO 45001, and ISO 50001 management systems certificates, it has a perspective that prioritizes quality, environmentalism, energy efficiency and prioritizes the safety of its employees and all other stakeholders.
    View product
  • Styronit Thermal Insulation Plaster

    Read more

     

    English EPD Document

      EPD document prepared for Styronit Thermal Insulation Plaster with registration number S-P-03983 has been registered and published in EPD Turkey and The International EPD System. Registered EPD document applies to all global markets. STY 160 Kaba Natural thermal insulation plaster, applied internally and externally instead of classic rough plaster. It has a high breathing and adhesion ability. Suitable for interior and exterior wall surfaces, bricks, aerated concrete, pumice walls and ceiling. STY 300 Biomantolama Natural thermal insulation material, applied to the exterior walls of the painted buildings. High thermal comfort and high breathability  raises high the living comfort in buildings. It also has high adhesion and water repellent ability. Suitable for exterior painted surfaces STY 325 Bioklima Natural thermal insulation material, applied to the interior walls of the painted buildings. High thermal comfort and high breathability  raises high the living comfort in buildings and creates a bioclimatic natural environment. The ability to reflect heat, helps to protect the thermal energy saving even on 1 cm thickness. Suitable for interior painted walls, cold storages, schools, conference rooms, ect, STY 325 Acoustic Natural plaster, applied to prevent  noise problems to  neighboring  walls, elevators, generator rooms, offices, schools, conference rooms hotels..ect. Suitable for interior wall surfaces, bricks,  aerated concrete, pumice walls, ceiling STY 355 Acoustic Plus Natural plaster, applied to prevent  noise problems to  neighboring  walls, elevators, generator rooms, offices, schools, conference rooms hotels..ect. Suitable for interior wall surfaces, bricks,  aerated concrete, pumice walls, ceiling STY 550 Şap It is a lightweight screed for thermal and acoustic insulation. This lightweight screeds is applied on ventilated roofs, flat roofs, floors, balconies and terraces before marble, ceramic, parquet, laminate and PVC STY HRSN Horasan Natural plaster for renovation,  restoration of historical buildings, domed mosque and also grouting plaster to fill the gaps and used for acoustic and thermal insulation. Used on the domed mosque, interior and exterior walls of historical buildings, church, wood and stone surfaces STYRONIT Styronit Doğal Yalıtım Malz. San ve Tic A.Ş. minimizes the energy consumption in the buildings with its’ natural thermal and acoustic insulation products under Styronit® brand. With our experienced technical and administrative staf services set the standard of excellence in domestic and international markets including; thermal insulation and acoustic insulation plasters. Styronit with EN-ISO 9001: 2015 and EN ISO 14001: 2015 certificates and social responsibilities contributes in the development of environmentally friendly green buildings for the future of Turkey and the world. So far Styronit is the first company in Turkey to certify Type III EPD (Environmental Product Declaration) certification system for thermal, acoustic and fire insulation plaster products. Therefore Styronit provides high scores to its’ customer’s green building projects from LEED, BREEAM. With its’ 5000 m² closed area, our company has more than 10 years experiences in environmentally friendly products in the insulation industry. Thanks to our innovative R&D efforts that has increased the quality and variety of our products from day to day.      
    View product
  • Çimsa RECIPRO40® – Calcium Aluminate Cement

    Read more

    English EPD Document

      EPD document prepared for Çimsa RECIPRO40® - Calcium Aluminate Cement with registration number S-P-02236 has been registered and published in EPD Turkey and The International EPD System. Registered EPD document applies to all global markets. The declared product is Çimsa RECIPRO40 - Calcium Aluminate Cement (RECIPRO40) manufactured in accordance with /EN14647/. RECIPRO40 is defined under the special cement class. Calcium aluminate cement is composed of hydraulic calcium aluminates as main constituent. Cement is the adhesive or glue which, when sets, binds particles of fine aggregate together to produce mortar. When mixed with water the cement forms a paste called the fine matrix. Cements are hydraulic materials, this means that they depend upon a reaction with water rather than air for strengthening. When water is added to cement a chemical reaction called hydration commences immediately. The reaction continues while water is still present. After hardening, it retains its strength and stability even under water. ÇİMSA Çimsa, which is an affiliate of Sabancı Holding, was established in Mersin in 1972. Today, Çimsa runs its manufacturing operations through its 5 integrated factories in Mersin, Eskişehir, Kayseri, Niğde and Afyonkarahisar, and its grinding plant in Ankara. Being one of the leading brands in white cement around the world, Çimsa continues its operations in the international arena through Cimsa Sabanci Cement BV, which was formed by combining its operational capability with the financial strength of Sabancı Holding, its main shareholder. Thanks to its market-oriented approach and large distribution network, Çimsa fully meets the needs of its customers in a timely manner. As a reliable business partner for its stakeholders, it provides the necessary supplies to build living spaces and infrastructure for the next generations. Çimsa leads the Turkish cement and construction materials industry in innovation with its special products such as white cement and calcium aluminate cement, as well as gray cement. Driving value and focusing on profitable growth for all of its stakeholders, Çimsa also aims to maintain this in the future.
    View product
  • Dalsan DERZTEK-Jointing Compound

    Read more

     

    English EPD Document

      EPD document prepared for Dalsan DERZTEK-Jointing Compound with registration number S-P-04049 has been registered and published in EPD Turkey and The International EPD System. Registered EPD document applies to all global markets. DERZTEK is a jointing compound which is used at COREX plasterboard joints over joint tapes. DERZTEK is easy to apply. Special additives in its structure retard the absorption of its moisture by the plasterboard surface. As well as functioning as a filler, DERZTEK also forms a smooth surface as a result of its special grain- size distribution. DERZTEK is highly adhesive. As it is a breathable material, by balancing the humidity DERZTEK creates a healthier environment. Because DERZTEK is so flexible, the plasterboard will not crack at the joints and will flex as one single surface. DERZTEK is GREENGUARD certificated product that shows the effects of our products on indoor air quality.   DALSAN DALSAN is an ineradicable company almost as old as Turkish Republic, commenced the fabrication of plaster in industrial level for our country that plaster was formerly used as a healthy, durable and material of construction individually since 9000’s B.C. in Anatolia. DALSAN has developed first workshop establishment from fabrication of teeth plaster by baking and pestling them in neighborhood bakery oven, commenced on 1932. Today, DALSAN Alçı has fabrication capacity of more then 1 million ton of gypsum and cement based products by using modern and high technology in facilities location in Gebze and Ankara. Additionally, galvanized profiles used in drywall systems are also fabricated in these facilities. DALSAN increases the share in market by the aim of true and qualified product delivery to customers as well as qualified and honesty based fabrication. DALSAN succeeded to become a constantly learning institution by caring and monitoring tendencies, expectations, different acknowledges of sector. Importance given on learning among structure of company provides a basis to variety of product range and meet demands of consumers effectively. Continuous learning habit dominant in DALSAN accompanied with information and talent constitutes the most important dynamic of a better and eco-friendly fabrication. DALSAN is a manufacturer with high export potential due to its location. Today, DALSAN exports to almost 70 countries in the world from both Gebze and Ankara plants. DALSAN certifies that the goods and services to its customers are supplied with the internationally accepted ISO 9001 Quality Management System. Together with ISO 9001 Quality Management,DALSAN follows and applies ISO 14001 Environmental Management System. Prior aim of DALSAN for the future is, to be on the top of the line in the technological competition made in plaster and plaster board fabrication by developing the fabrication more and more. Under favour of accumulation of knowledge and importance given to research and development studies, we offer all the needs of a construction from floor to roof.  
    View product
  • Dalsan ADERTEK- Gypsum Based Adhesive

    Read more

     

    English EPD Document

      EPD document prepared for Dalsan ADERTEK- Gypsum Based Adhesive with Perlite with registration number S-P-04048 has been registered and published in EPD Turkey and The International EPD System. Registered EPD document applies to all global markets. ADERTEK is a construction plaster that is used for bonding COREX, expanded polystyrene (EPS), extruded polystyrene (XPS), mineral wools (glasswool, rockwool) and composite insulation panels to surfaces such as brick, concrete, aerated concrete etc. It is the most convenient product for direct bonding applications where volume loss could be minimized by keeping wall as thin as possible. Because it is a breathable material, ADERTEK leads to a healthier environment by stabilizing humidity. It has highly adhesive properties Its strength increases quickly after setting.   DALSAN DALSAN is an ineradicable company almost as old as Turkish Republic, commenced the fabrication of plaster in industrial level for our country that plaster was formerly used as a healthy, durable and material of construction individually since 9000’s B.C. in Anatolia. DALSAN has developed first workshop establishment from fabrication of teeth plaster by baking and pestling them in neighborhood bakery oven, commenced on 1932. Today, DALSAN Alçı has fabrication capacity of more then 1 million ton of gypsum and cement based products by using modern and high technology in facilities location in Gebze and Ankara. Additionally, galvanized profiles used in drywall systems are also fabricated in these facilities. DALSAN increases the share in market by the aim of true and qualified product delivery to customers as well as qualified and honesty based fabrication. DALSAN succeeded to become a constantly learning institution by caring and monitoring tendencies, expectations, different acknowledges of sector. Importance given on learning among structure of company provides a basis to variety of product range and meet demands of consumers effectively. Continuous learning habit dominant in DALSAN accompanied with information and talent constitutes the most important dynamic of a better and eco-friendly fabrication. DALSAN is a manufacturer with high export potential due to its location. Today, DALSAN exports to almost 70 countries in the world from both Gebze and Ankara plants. DALSAN certifies that the goods and services to its customers are supplied with the internationally accepted ISO 9001 Quality Management System. Together with ISO 9001 Quality Management,DALSAN follows and applies ISO 14001 Environmental Management System. Prior aim of DALSAN for the future is, to be on the top of the line in the technological competition made in plaster and plaster board fabrication by developing the fabrication more and more. Under favour of accumulation of knowledge and importance given to research and development studies, we offer all the needs of a construction from floor to roof.  
    View product
  • Dalsan KARTEK- Cornice Plaster

    Read more

     

    English EPD Document

      EPD document prepared for Dalsan KARTEK- Cornice Plaster with Perlite with registration number S-P-04047 has been registered and published in EPD Turkey and The International EPD System. Registered EPD document applies to all global markets. KARTEK, is a plaster used for the production of decorative elements like cornices. Its working time enables easy application with low wastage. KARTEK is easy-to-mix. Because it is a breathable material, KARTEK helps create a healthier environment by stabilizing the humidity. KARTEK has high resistance and surface hardness. Because of its fine grain- size, KARTEK produces a smooth cast surface.   DALSAN DALSAN is an ineradicable company almost as old as Turkish Republic, commenced the fabrication of plaster in industrial level for our country that plaster was formerly used as a healthy, durable and material of construction individually since 9000’s B.C. in Anatolia. DALSAN has developed first workshop establishment from fabrication of teeth plaster by baking and pestling them in neighborhood bakery oven, commenced on 1932. Today, DALSAN Alçı has fabrication capacity of more then 1 million ton of gypsum and cement based products by using modern and high technology in facilities location in Gebze and Ankara. Additionally, galvanized profiles used in drywall systems are also fabricated in these facilities. DALSAN increases the share in market by the aim of true and qualified product delivery to customers as well as qualified and honesty based fabrication. DALSAN succeeded to become a constantly learning institution by caring and monitoring tendencies, expectations, different acknowledges of sector. Importance given on learning among structure of company provides a basis to variety of product range and meet demands of consumers effectively. Continuous learning habit dominant in DALSAN accompanied with information and talent constitutes the most important dynamic of a better and eco-friendly fabrication. DALSAN is a manufacturer with high export potential due to its location. Today, DALSAN exports to almost 70 countries in the world from both Gebze and Ankara plants. DALSAN certifies that the goods and services to its customers are supplied with the internationally accepted ISO 9001 Quality Management System. Together with ISO 9001 Quality Management,DALSAN follows and applies ISO 14001 Environmental Management System. Prior aim of DALSAN for the future is, to be on the top of the line in the technological competition made in plaster and plaster board fabrication by developing the fabrication more and more. Under favour of accumulation of knowledge and importance given to research and development studies, we offer all the needs of a construction from floor to roof.  
    View product
  • Dalsan SONTEK-Thin Coat Plaster

    Read more

     

    English EPD Document

      EPD document prepared for Dalsan SONTEK-Thin Coat Plaster with Perlite with registration number S-P-04046 has been registered and published in EPD Turkey and The International EPD System. Registered EPD document applies to all global markets. SONTEK is a gypsum- based thin plaster which is used as a top coat plaster with its high adhesion strength. SONTEK applied on surfaces which are gypsum plaster, cement plaster and plasterboard. Special additives in its formulation delay the absorption of SONTEK mortar’s water by the substrate. SONTEK can be applied easily. Corrects cracks and defects on the surfaces. Prepares smooth surfaces for SATENTEK finishing plaster. SONTEK creates a smooth surface and reduces the finishing plaster usage.   DALSAN DALSAN is an ineradicable company almost as old as Turkish Republic, commenced the fabrication of plaster in industrial level for our country that plaster was formerly used as a healthy, durable and material of construction individually since 9000’s B.C. in Anatolia. DALSAN has developed first workshop establishment from fabrication of teeth plaster by baking and pestling them in neighborhood bakery oven, commenced on 1932. Today, DALSAN Alçı has fabrication capacity of more then 1 million ton of gypsum and cement based products by using modern and high technology in facilities location in Gebze and Ankara. Additionally, galvanized profiles used in drywall systems are also fabricated in these facilities. DALSAN increases the share in market by the aim of true and qualified product delivery to customers as well as qualified and honesty based fabrication. DALSAN succeeded to become a constantly learning institution by caring and monitoring tendencies, expectations, different acknowledges of sector. Importance given on learning among structure of company provides a basis to variety of product range and meet demands of consumers effectively. Continuous learning habit dominant in DALSAN accompanied with information and talent constitutes the most important dynamic of a better and eco-friendly fabrication. DALSAN is a manufacturer with high export potential due to its location. Today, DALSAN exports to almost 70 countries in the world from both Gebze and Ankara plants. DALSAN certifies that the goods and services to its customers are supplied with the internationally accepted ISO 9001 Quality Management System. Together with ISO 9001 Quality Management,DALSAN follows and applies ISO 14001 Environmental Management System. Prior aim of DALSAN for the future is, to be on the top of the line in the technological competition made in plaster and plaster board fabrication by developing the fabrication more and more. Under favour of accumulation of knowledge and importance given to research and development studies, we offer all the needs of a construction from floor to roof.  
    View product
  • Dalsan SATENTEK- Finishing Plaster

    Read more

     

    English EPD Document

      EPD document prepared for Dalsan SATENTEK- Finishing Plaster with Perlite with registration number S-P-04045 has been registered and published in EPD Turkey and The International EPD System. Registered EPD document applies to all global markets. SATENTEK, with its high adherence, is a finishing plaster used as an undercoat for all types of painting. SATENTEK, can be applied to SIVATEK and COREX plasterboard surfaces. Its long workability time enables an easy application with a low waste rate. Special additives in its formulation delay the absorption of SATENTEK mortar’s water by the substrate. As it is a breathable material, by regulating humidity SATENTEK leads to a healthier environment. SATENTEK’s paste-like texture makes it easy to apply. As it is a breathable material, by regulating humidity SATENTEK leads to a healthier environment. SATENTEK is GREENGUARD certificated product that shows the effects of our products on indoor air quality.   DALSAN DALSAN is an ineradicable company almost as old as Turkish Republic, commenced the fabrication of plaster in industrial level for our country that plaster was formerly used as a healthy, durable and material of construction individually since 9000’s B.C. in Anatolia. DALSAN has developed first workshop establishment from fabrication of teeth plaster by baking and pestling them in neighborhood bakery oven, commenced on 1932. Today, DALSAN Alçı has fabrication capacity of more then 1 million ton of gypsum and cement based products by using modern and high technology in facilities location in Gebze and Ankara. Additionally, galvanized profiles used in drywall systems are also fabricated in these facilities. DALSAN increases the share in market by the aim of true and qualified product delivery to customers as well as qualified and honesty based fabrication. DALSAN succeeded to become a constantly learning institution by caring and monitoring tendencies, expectations, different acknowledges of sector. Importance given on learning among structure of company provides a basis to variety of product range and meet demands of consumers effectively. Continuous learning habit dominant in DALSAN accompanied with information and talent constitutes the most important dynamic of a better and eco-friendly fabrication. DALSAN is a manufacturer with high export potential due to its location. Today, DALSAN exports to almost 70 countries in the world from both Gebze and Ankara plants. DALSAN certifies that the goods and services to its customers are supplied with the internationally accepted ISO 9001 Quality Management System. Together with ISO 9001 Quality Management,DALSAN follows and applies ISO 14001 Environmental Management System. Prior aim of DALSAN for the future is, to be on the top of the line in the technological competition made in plaster and plaster board fabrication by developing the fabrication more and more. Under favour of accumulation of knowledge and importance given to research and development studies, we offer all the needs of a construction from floor to roof.  
    View product
  • Dalsan SIVATEK- Manual Plaster with Perlite

    Read more

     

    English EPD Document

      EPD document prepared for Dalsan SIVATEK- Manual Plaster with Perlite with registration number S-P-04044 has been registered and published in EPD Turkey and The International EPD System. Registered EPD document applies to all global markets. SIVATEK is a gypsum- based, specially formulated ready-to-use bagged plaster that can be applied directly to brick, concrete, aerated concrete, etc. Its long workability time enables an easy application with a low waste rate. SIVATEK does not slump while setting on the surfaces to which it is applied. It has high strength, surface hardness and adherence. Because it is a breathable material, by regulating humidity SIVATEK leads to a healthier environment. It is a non-combustible material. The water in its structure helps retard fire. It does not cause mould, bacterial or fungal growth. SIVATEK is GREENGUARD certificated product that shows the effects of our products on indoor air quality.   DALSAN DALSAN is an ineradicable company almost as old as Turkish Republic, commenced the fabrication of plaster in industrial level for our country that plaster was formerly used as a healthy, durable and material of construction individually since 9000’s B.C. in Anatolia. DALSAN has developed first workshop establishment from fabrication of teeth plaster by baking and pestling them in neighborhood bakery oven, commenced on 1932. Today, DALSAN Alçı has fabrication capacity of more then 1 million ton of gypsum and cement based products by using modern and high technology in facilities location in Gebze and Ankara. Additionally, galvanized profiles used in drywall systems are also fabricated in these facilities. DALSAN increases the share in market by the aim of true and qualified product delivery to customers as well as qualified and honesty based fabrication. DALSAN succeeded to become a constantly learning institution by caring and monitoring tendencies, expectations, different acknowledges of sector. Importance given on learning among structure of company provides a basis to variety of product range and meet demands of consumers effectively. Continuous learning habit dominant in DALSAN accompanied with information and talent constitutes the most important dynamic of a better and eco-friendly fabrication. DALSAN is a manufacturer with high export potential due to its location. Today, DALSAN exports to almost 70 countries in the world from both Gebze and Ankara plants. DALSAN certifies that the goods and services to its customers are supplied with the internationally accepted ISO 9001 Quality Management System. Together with ISO 9001 Quality Management,DALSAN follows and applies ISO 14001 Environmental Management System. Prior aim of DALSAN for the future is, to be on the top of the line in the technological competition made in plaster and plaster board fabrication by developing the fabrication more and more. Under favour of accumulation of knowledge and importance given to research and development studies, we offer all the needs of a construction from floor to roof.  
    View product
  • Dalsan Maxitek Gypsum Based Plaster

    Read more

     

    English EPD Document

      EPD document prepared for Dalsan Maxitek Gypsum Based Plaster with registration number S-P-04043 has been registered and published in EPD Turkey and The International EPD System. Registered EPD document applies to all global markets. MAXITEK, silobas ile sevk edilen alçı bazlı hazır makine sıvasıdır. Tuğla, beton, brüt beton, gazbeton, bimsblok vb. malzemeler üzerine doğrudan uygulanır. Yüksek yüzey sertliğine sahiptir. Nefes alan bir malzeme olduğundan nem oranını dengeleyerek sağlıklı bir ortam oluşturur. MAXITEK, iş gücünü artırır, uygulamacıyı yükten, şantiyeyi ise torba atığından kurtarır. MAXITEK, özel formülü sayesinde silodan pnömatik sistem ile taşınabilme özelliğine sahiptir. Yanmaz bir malzemedir. Bünyesindeki kristal sudan dolayı yangın geciktirici özelliğe sahiptir.   DALSAN DALSAN is an ineradicable company almost as old as Turkish Republic, commenced the fabrication of plaster in industrial level for our country that plaster was formerly used as a healthy, durable and material of construction individually since 9000’s B.C. in Anatolia. DALSAN has developed first workshop establishment from fabrication of teeth plaster by baking and pestling them in neighborhood bakery oven, commenced on 1932. Today, DALSAN Alçı has fabrication capacity of more then 1 million ton of gypsum and cement based products by using modern and high technology in facilities location in Gebze and Ankara. Additionally, galvanized profiles used in drywall systems are also fabricated in these facilities. DALSAN increases the share in market by the aim of true and qualified product delivery to customers as well as qualified and honesty based fabrication. DALSAN succeeded to become a constantly learning institution by caring and monitoring tendencies, expectations, different acknowledges of sector. Importance given on learning among structure of company provides a basis to variety of product range and meet demands of consumers effectively. Continuous learning habit dominant in DALSAN accompanied with information and talent constitutes the most important dynamic of a better and eco-friendly fabrication. DALSAN is a manufacturer with high export potential due to its location. Today, DALSAN exports to almost 70 countries in the world from both Gebze and Ankara plants. DALSAN certifies that the goods and services to its customers are supplied with the internationally accepted ISO 9001 Quality Management System. Together with ISO 9001 Quality Management,DALSAN follows and applies ISO 14001 Environmental Management System. Prior aim of DALSAN for the future is, to be on the top of the line in the technological competition made in plaster and plaster board fabrication by developing the fabrication more and more. Under favour of accumulation of knowledge and importance given to research and development studies, we offer all the needs of a construction from floor to roof.  
    View product